If you are considering upgrading your bathroom and kitchen sink faucets, you have come to the right place. The following explanation will make your task much easier and will save your time as well.
However, before we start, make sure that you have following materials ready with you.
- New faucet assembly
- Basin wrench
- Adjustable wrenches
- Slip-joint pliers
- Scouring pad
Now follow these simple steps. (Assuming that you are replacing the old two-handled faucet with the more modern single-handled type)
Replacing Kitchen Sink Faucets
1. Before you start, go at the shut-off valves under the sink, and turn off the water.
2. Open the faucet so that it could drain any excess water.
3. The next step is to disconnect the hot and cold water supply lines from the shutoff valves. You can use a small adjustable-wrench to do this.
4. Reach up behind the faucet. You will find the coupling nuts that connect the supply tubes to the faucet. Unscrew the same using a basin wrench.
5. Behind the faucet, you will also find mounting nuts that hold the faucet in place. Remove these nuts using the same basin wrench.
6. Now that you have disconnected the mounting nuts, you can lift out the old faucet. Lifting it out, disconnect the sprayer hose from the assembly using an adjustable wrench.
7. Lift out the sprayer hose, and remove the faucet.
8. Once you have removed the faucet, clean the surface of the sink thoroughly with a scouring pad.
9. Remove the escutcheon cap and replace the same with the one that is included with your new faucet.
10. Now you are ready to make the new connection. Bring your new sprayer hose, and slip it down through the sprayer hole.
11. Feed the sprayer hose up through the center faucet hole, and connect the hose through the sprayer nipple using an adjustable wrench.
12. If the hot and cold supply tubes of the new faucet have a different length, attach flexible connectors to the fittings on the supply tubes. Hold the faucet fitting stationary with one wrench and tighten each connection with another wrench.
13. Insert and feed the supply lines and the connectors into the center hole, and then seat the faucet.
14. Now crawl up under the sink and in order to hold the faucet in place, install a washer and nut to the end bolts.
15. First, tighten the nuts by hand, and then with a basin wrench.
16. Connect the supply lines to the shutoff valves, and turn the water on.
17. Turn on the faucet and check for leaks.
Replacing Bathroom Sink Faucets
1. Go underneath the sink. Turn off the water. Loosen the collar nuts on the drainpipe.
2. Drain any excessive water, and then remove the drainpipe.
3. Loosen the nuts that hold the pop-up assembly in place under the sink using slip-joint pliers.
4. Unscrew the pop-up flange in order to free the assembly underneath the sink.
5. Remove the fittings that join the supply lines of the old faucet to the shutoff valves, using a wrench.
6. Repeat the steps 4-15 as explained above for replacing kitchen faucet.
7. Now, you have to install the pop-up assembly.
8. Push the pop-up rod down through the body of the faucet.
9. Attach the flat bar.
10. At the bottom of the new flange, use a little plumber’s putty to hold the tailpiece so that the whole assembly protrudes up through the drain hole in the sink.
11. Spin the ring to position the same with the tailpiece under the sink.
12. In order to secure pop-up housing in place, tighten the nut on top of the tailpiece.
13. Hook up the pop-up lever onto the flat bar in order to secure it to the pop-up housing.
14. Drop the stopper into the drain hole.
15. Replace the drainpipe.
16. Tighten the collar nuts.
17. Turn on the faucet and check for leaks.
Hence, replacing a kitchen and a bathroom faucet is almost similar except for the work related to the pop-up assembly that is included with the bathroom sink.
How to Install a Pullout Kitchen Sink Faucet-Pull out kitchen faucet
Change your existing faucet and get a handle on the process. Things You’ll Need: Pullout Kitchen Sink Faucet. Adjustable wrench; Plumber’s putty; Towel; Bucket; Flashlight (if needed); Pullout faucet. A stiff-necked kitchen faucet with a little swivel head clutters the back of your sink, what with the spigot, the hot and cold handles, and that squat black spray hose (which, let’s face it, always leaks). The current trend in faucets is a single, … Kitchen & Bath Links:
Replacing a bathroom faucet, easily. | Bukisa.com
Turn off water on hot and cold angle stops under kitchen or vanity cabinet. Remove supply lines going into angle stops with a sponge or small bucket under angle stop. Remove any hoses on valve body that will prevent the removal of faucet. … If there is no gap then cut you a piece of 1 ½ or 1 1/4 of pvc pipe to act as a spacer from your lock nut and washer hitting the sink that is in the way. When installing new faucet never put plumbers putty on any part of faucet.
Bathroom Design Ideas – Bathroom Faucet Repair-Faucet repair
Bathroom faucet: Create your own style and Design Your Own Bathroom. Complete your bathroom ideas by choosing your bathroom faucet, sink, countertop, wall.
The Best Kitchen Faucet Aerators »» MetaEfficient Reviews
This bath or kitchen sink aerator has a fingertip on/off control lever, and it’s rated at 2.5 GPM. It allows you to temporarily slow flow of water while maintaining water temperature. This aerator is available from Amazon for $6.50. … The Hot Water Lobster uses no electricity and works off of your existing plumbing! It’s also pump free, so it creates no noise. It’s made in the U.S.A., has a 10-year warranty, and can be easily installed in under 10 to 15 minutes!
Lesson to Replace Leaky Bathroom Faucets-Faucet Installation
This course might still be cheaper than calling a plumber who might just tell you to replace the sink anyway. STEP BY STEP Instructions to Replace a Leaky Bathroom Faucet …. Kitchen & Bath Links:
Mail this post
Technorati Tags: Bathroom Sink Faucets